Part Number: 74LS, Maunfacturer: Motorola, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor. 74LS datasheet, 74LS pdf, 74LS data sheet, datasheet, data sheet, pdf, Fairchild Semiconductor, 3-STATE Octal D-Type Transparent Latches and. products and disclaimers thereto appears at the end of this data sheet. 74LS SOP – NS. Tape and reel. SN74LSNSR. 74LS Tape and reel.
|Published (Last):||26 December 2013|
|PDF File Size:||9.17 Mb|
|ePub File Size:||1.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Results 1 to 20 of The led in the circuit is always Off. It doesnt latch in HIGH state. Can anyone please help 74ls33 sort out the problem?.
Datasheet of 74LS is also attached. Last edited by sharikbaig; 27th August at This means that while your Enable is active and in your circuit it is always active – pin 11 high then the data presented to an input will always immediately get reflected to the output.
As long as output is enabled which it is – pin 1 is Low For this latch to hold data, you must do the following: Enable gates pin 11 high 2. Place data on input pin 3 – i. You have LE fixed High, hence output equals input Need to either set LE low to latch the input or choose different latch. Originally Posted by kripacharya.
Here is an example http: The beauty of this simple circuit is it actually debounces your switch, i. Similar for other switch input. The only potential issue is both switches operating together as the output becomes indeterminate.
If you like I will draw the schematic for you.
Last edited by KerimF; 27th August at Being not a machine, I always do silly mistakes or miss important things. Therefore almost every post I write would usually be updated several times till it reaches its saturation: Also I may not reply at time. Our main server could be out of service anytime. Originally Posted by KerimF.
74ld373 you have CD, the remaining 2 gates can be used to combine the 2 switches in one. The initial state of the LED is off U3 output is low. The current I1, R7 and Q2 replace the push-button switch in order to simulate the circuit.
I will get ic’s by day after tomorrow, will try your schematic and update you soon.
Thanks also for reminder on LED driver, I had dropped down to logic states! You people are very helpful, Thanks. Any other idea is also welcomed.
74LS373 Datasheet PDF
Help with Latch IC 74LS based latching ciruit I actually made a similar project back in the 80’s when experimemting with programmable logic the good old days! Each momentary switch would latch a solenoid valve and when activated switch off the others valvesa bit like a manual washing machine.
This single chip solution plus solenoid drivers worked very well It could have been a useful touch switch which weren’t very common thenbut I learnt how to filter out, clamp and provide immunity instead!
These small chips were 18 or 24 pins? They were a great introduction to simple logic and hardware which is a bit lost in todays massive chips. Relay latching in AT89C51 based circuit Problem with 74LS latching! Compare latch based and register based design 5. Part and Inventory Search. AF modulator in Transmitter what is the A?
IC Datasheet: 74LS Data Sheet : Free Download, Borrow, and Streaming : Internet Archive
What is the function of TR1 in this circuit 3. Losses in inductor of a boost converter 9. Turn on power triac – proposed circuit analysis 0. Choosing IC with EN signal 2.
IC Datasheet: 74LS373 Data Sheet
Measuring air gap of a magnetic core for home-wound inductors and flyback transformer 7. Hierarchical block is unconnected 3. Digital multimeter appears to have measured voltages lower than expected. PV datawheet battery circuit 4. How reliable is it? Equating complex number interms of the other 6. CMOS Technology file 1.
74LS Datasheet(PDF) – TI store
ModelSim – How to force a struct type written in SystemVerilog? Input port and input output port declaration in top module 2. PNP transistor not working 2.
Distorted Sine output from Transformer 8. How can the power consumption for computing be reduced for energy fatasheet Dec 242: How do you get an MCU design to market quickly? Dec 248: Heat sinks, Part 2: Synthesized tuning, Part 2: The time now is