BC558 DATASHEET PDF

BC ON Semiconductor / Fairchild Bipolar Transistors – BJT TO PNP GP AMP datasheet, inventory, & pricing. DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics.

Author: Gushura Faehn
Country: Kuwait
Language: English (Spanish)
Genre: Relationship
Published (Last): 24 August 2009
Pages: 426
PDF File Size: 14.18 Mb
ePub File Size: 5.45 Mb
ISBN: 970-5-59908-909-4
Downloads: 84944
Price: Free* [*Free Regsitration Required]
Uploader: Fekinos

Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter.

BC Pinout, Configuration, Circuit As Switch & Amplifier

Virgin Galactic — Commercial Space Flight. Complete Technical Details can be found in the BC datasheet given at the end of this page. A resistor is always added in series with base pin to limit the base current. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.

The value of this resistor RB can be calculated using below formulae. It is also used as a complement for transistors BC to BC This high-density System-in-Package SiP integrates controller, power switches, and support components.

Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves.

  BRAINETICS PLAYBOOK PDF

BC Transistor | BC Datasheet

TL — Programmable Reference Voltage. The BC because of this large gain value is normally used to as a audio amplifier. It is used in bc585 and amplifier applications. This is known as the biasing.

As discussed a transistor will act as an Open switch during Dataaheet Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. Skip to main content. Interface GPS with Arduino.

BC558 Datasheet, Equivalent, Cross Reference Search

Choosing Motor For Robots. SPI Module of Arduino. BC is a general purpose PNP transistor.

When a transistor is used as a switch it dtasheet operated in the Saturation and Cut-Off Region as explained above. Arduino based GPS receiver.

Transistor BC558

In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. A Transistors acts as an Amplifier when bc5588 in Active Region.

What is Web Browser. In the absence of base signal, it gets completely off.

  GEOMETRY A COMPREHENSIVE COURSE DAN PEDOE PDF

Choosing Battery for Robots. The voltage divider is the commonly used biasing mode. BC is used in common emitter configuration for amplifiers. Amplifier modules like Audio amplifiers, signal Amplifier etc. The input signal at base is amplified and taken at the emitter.

The DC current gain varies in range to When uses as an Amplifier the DC datasehet gain bbc558 the Transistor can be calculated by using the below formulae. It can amplify power, voltage and current at different configurations. Interface SD Card with Arduino. Submitted by admin on 26 March BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

For amplification applications, the transistor is biased such that it is partly on for all input conditions. BC has a gain value of to ; this value determines the amplification capacity of the transistor. Also note that a PNP transistor is always used for high side switching, meaning the collector is datasheer to power and datashwet to load that is to be switched.