GY520 MANUAL PDF

Futaba GY Pdf User Manuals. View online or download Futaba GY Instruction Manual. Nstruction, Anual • Read online or download PDF • Futaba GY User Manual. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure. Note that I have seen.

Author: Makinos Vuramar
Country: Luxembourg
Language: English (Spanish)
Genre: History
Published (Last): 2 August 2018
Pages: 181
PDF File Size: 9.83 Mb
ePub File Size: 10.36 Mb
ISBN: 671-7-63500-842-1
Downloads: 89583
Price: Free* [*Free Regsitration Required]
Uploader: Kajijinn

On smaller helicopters the flybar can swing down low enough to reach a gyro mounted on the top of the framset.

Adjust the guides to acheive the least resistance. Blue – Standard Response default selection Red – Fast Response for lightweight small nanual with a fast tail servo Violet – Slow Response for scale helis To change the mode, quickly press and release the button on the gyro. Wait three seconds for it to initialize. This will set it up for the next step.

Futaba GY Gyro How-to

Quote message in reply? It will take about 3 seconds for the gyro to initialize. On a larger class 50 size it might be in the 80 to range.

The signal wire will be next to the labels on the receiver. Then the light will stay on solid. Once you set the travel for this side, quickly press and release the button on the gyro.

For a small heli, class ex. Keep the gh520 control link off of the servo. The servo needs to rotate in the direction that would cause the trailing edge of the tail blades to move to the right side of the helicopter. Snap the link on the servo and check that you do not get binding at full left and full right. Also make sure the rudder trim under the rudder stick is centered. The first thing to do is gt520 the link slides as free as possible.

  LG VX8000 MANUAL PDF

In order to be able to post messages on the HeliFreak forums, you must manaul register. At this time we need to check that the radio is correctly controlling the gyro. If not, hold the button down to enter setup mode. Blue – F3C degrees per second Red – 3D degrees per second To change the mode, quickly press and release the button on the gyro. Heading Hold Solid Blue: That is the difference between one value having a positive value and the other a negative value. You may want it faster or slower so change the value appropiately.

Once you get the link as free from resistance as you can, you need find a position for servo arm. One direction will set the gain value for heading hold and the other will be for standard rate.

Register Now In order to be able to post messages on the HeliFreak forums, you must first register. On the Trex not Pro some people turn the block upside down that the tail boom goes in then mount the gyro gy250 the rear of the frameset.

If you need to readjust then quickly press and release the gyro button. Hold the button on the gyro for 2 seconds to go to the next function. Manaul disconnect the rudder link from the tail servo. If you the tail wags in flight then decrease the gain. The chart below works for almost all helicopters but you should consult your helicopter manual if you are not sure.

Futaba GY User Manual | 32 pages

Hold in the button on the gyro for three seconds. Use a real email address or you will not be granted access to the site. Also note that I added a slight bend to the front section of the tail control rod so that the link is at the same height as the ball on the servo arm. Note maanual I have seen common problems with the tail blades grips flipped the wrong direction and the tail belt twisted the wrong mamual.

  BURNE HOGARTH DYNAMIC LIGHT AND SHADE PDF

Thank you so much! This will set how fast the helicopter rotates.

If you do not have a hole exactly 90 degrees then take the servo arm off and rotate it to another position. Just because you plan to fly 3D does not mean you need to set the gyro to 3D mode. Now power off the receiver and plug the tail servo up to the gyro. The gyro will repeat a ‘1 blink’. A high framerate setting on a low framerate servo will damage the servo in a minute. Use a marker to write on the label ‘R’, ‘G’, and ‘S’ as shown in the bottom picture to the left. Now that you have found a position for the servo arm you need to mount the ball on it.

FUTABA GY520 Instruction Manual Page 23

If everything was okay then the light on the gyro will momentarily change to violet and the servo will travel to the other side. The color of this 4-Blink indicates the mode it is in.

In a moment you will turn on the receiver. Move the nose fy520 the helicopter left and verify the trailing edge of the tail blades move to the right.